Search found 10 matches
- Sat Dec 20, 2014 7:07 am
- Forum: **GENERAL TECHNICAL HELP**
- Topic: Need clutch slave heim joint sleeve!???? Where?
- Replies: 2
- Views: 357
Re: Need clutch slave heim joint sleeve!???? Where?
no one carries this sleeve, joint, arm anymore. the best solution if this happens to you is... if sleeve is not blown to shreds, simply grind down and a bit past the damaged area. take note of the amount you have removed. Go to a local ace, or tractor supply, or true value and purchase a fine thread...
- Sat Dec 20, 2014 7:02 am
- Forum: **GENERAL TECHNICAL HELP**
- Topic: Diameter of clutch and pressure plates?
- Replies: 2
- Views: 435
Re: Diameter of clutch and pressure plates?
Called HR Clutch and Joe is great. Drove to Bensalem, PA to pick-up and have flywheel resurfaced. In and out in 20 mins. Great SHOP! I have a 10 spline, 10" disc and 1" input shaft. I found only one other place that had this setup and they said LUK clutches makes one. They are in Leola, PA and quote...
- Tue Nov 18, 2014 8:33 am
- Forum: **GENERAL TECHNICAL HELP**
- Topic: Need clutch slave heim joint sleeve!???? Where?
- Replies: 2
- Views: 357
Need clutch slave heim joint sleeve!???? Where?
Over adjusted the bullet like sleeve that goes over the heim joint threads on my slave cylinder and mushroomed the sleeve. I cannot find a replacement anywhere. Any suggestions? It's 3 3/8" long and inside diameter slides over 9/16" fine thread shaft. I did see an aftermarket adjustable master rod k...
- Tue Nov 18, 2014 8:25 am
- Forum: **GENERAL TECHNICAL HELP**
- Topic: Diameter of clutch and pressure plates?
- Replies: 2
- Views: 435
Diameter of clutch and pressure plates?
Looking to save time by ordering before replacing. Anyone know size of clutch and pressure plate 10" or 11"? Also dia. Of Piolet bushing and throwout bearing?
1967 D100 3.7L 225cu L6
4x2 RWD
Standard trans.
1967 D100 3.7L 225cu L6
4x2 RWD
Standard trans.
- Sun Nov 09, 2014 1:37 pm
- Forum: *ELECTRICAL/GAUGES/LIGHTING HELP*
- Topic: LENGTH OF WIRES - WIRING DIAGRAM '67 D100
- Replies: 1
- Views: 447
LENGTH OF WIRES - WIRING DIAGRAM '67 D100
Does anyone have a wiring diagram with proper lengths of wire needed to run, or a capacity chart stating the Watts, Amps or Volts needed to enter/exit each component? Or possibly thoughts on how to find out the necessary energy needed at each wire run to enter the component(s) on this model and year...
- Mon Nov 03, 2014 8:28 am
- Forum: **GENERAL TECHNICAL HELP**
- Topic: Wiring Questions: Firewall, connectors, etc: 1967 D100 3.7L
- Replies: 3
- Views: 318
Re: Wiring Questions: Firewall, connectors, etc: 1967 D100 3
I assume use the dioel. Grease as well?
And thank you for reply
And thank you for reply
- Mon Nov 03, 2014 12:14 am
- Forum: **GENERAL TECHNICAL HELP**
- Topic: Yet another "Truck wont start"
- Replies: 8
- Views: 567
Re: Yet another "Truck wont start"
same issue this weekend. if you have spark and is gapped appropriately. You can check the voltage at the varying areas. Coil, ballast, voltage reg. the quickest way is to jump the ballast to make sure the coil is not bad. get a 14 gauge wire connect positive to coil it will be marked on the coil as ...
- Sun Nov 02, 2014 11:52 pm
- Forum: **GENERAL TECHNICAL HELP**
- Topic: Wiring Questions: Firewall, connectors, etc: 1967 D100 3.7L
- Replies: 3
- Views: 318
Wiring Questions: Firewall, connectors, etc: 1967 D100 3.7L
Can I get automotive grade connectors, bulkhead, for the bullet connector wiring in the 67' D100 225 3.7L? Is it possible to just replace all the wires with the appropriate gauges and bullet connectors, pin, recept, etc. instead of buying the wiring harness? There is a myriad of options for purchasi...
- Sun Nov 02, 2014 11:20 pm
- Forum: **GENERAL TECHNICAL HELP**
- Topic: NEED '67 D100 BRAKE LINE DIAGRAM !!!!!
- Replies: 3
- Views: 603
Re: NEED '67 D100 BRAKE LINE DIAGRAM !!!!!
Thank you to all that helped.
proportioning valve set up and installed and tested. Used the copper/nic lines to replace the corroded steel lines throughout. Will follow-up with a picture when I get a chance with specs of each fitting.
Best
proportioning valve set up and installed and tested. Used the copper/nic lines to replace the corroded steel lines throughout. Will follow-up with a picture when I get a chance with specs of each fitting.
Best
- Sun Jul 06, 2014 9:44 pm
- Forum: **GENERAL TECHNICAL HELP**
- Topic: NEED '67 D100 BRAKE LINE DIAGRAM !!!!!
- Replies: 3
- Views: 603
NEED '67 D100 BRAKE LINE DIAGRAM !!!!!
NEED TO KNOW THE LINES THAT GO TO THE PROPORTIONING VALVE. I HAVE A 225 L6 2WD MANUAL. PICTURES WILL HELP TREMENDOUSLY!!!! I HAVE THE REPAIR MANUAL BUT DOES NOT READ ACCURATELY TO THE TRUCK. I DO NOT KNOW WHAT LINES AND WHERE THEY GO INTO THE PROPORTIONING VALVE. I DO NOT KNOW WHERE THE REAR ONE GOE...